Search Results

Dual Phase (DP) high strength steel is widely used in Europe and Japan for automotive component applications, and has recently drawn greater attention in the North American automotive industry for improving crash performance and reducing weight. In comparison with high-strength low-alloy (HSLA) steel grades with similar initial yield strength, DP steel has the following advantages: higher strain hardening, higher energy absorption, higher fatigue strength, higher bake hardenablility, and no yield point elongation. This paper compares the performance of DP and HSLA steel grades before, during, and after hydroforming. Computer simulation results show that DP steel demonstrates more uniform material flow during hydroforming, better crash performance and less wrinkling tendency.

This case study presents a new automated production noise test for power steering pumps. The test included adaptive noise cancellation, and a neural network implementation. The result mapped the pump acceleration signature into an objective repeatable noise metric. The test algorithm was a distributed DSP architecture designed for real-time measurement and decision processing. It was implemented with no increase in test cycle time. It accomplished the correlation of in-vehicle power steering pump noise to it's vibration characteristics, and retrofitting of accelerometers in place of microphones for acceptance testing.

Automatic headway control is an evolutionary step towards an automatic vehicle guidance and control system. This system expands the capability of the currently available production option-speed control. This paper describes the system from a theoretical and hardware viewpoint, with emphasis on the control logic. The electronic and electromechanical hardware design based on the theory presented is fully described. The limitations and advantages of the system are explained, based on test results from actual trial runs on an implemented vehicle. Capacity and safety benefits are made somewhat tangible by direct comparison with test results obtained on a roadway similar to that for which this system is recommended, under test conditions directly analogous to the operating characteristics of the automatic headway control system.

To improve the energy absorption capacity of front-end structures during a vehicle crash, a novel 12-sided cross-section was developed and tested. Computer-aided engineering (CAE) studies showed superior axial crash performance of the 12-sided component over more conventional cross-sections. When produced from advanced high strength steels (AHSS), the 12-sided cross-section offers opportunities for significant mass-savings for crash energy absorbing components such as front or rear rails and crush tips. In this study, physical crash tests and CAE modeling were conducted on tapered 12-sided samples fabricated from AHSS. The effects of crash trigger holes, different steel grades and bake hardening on crash behavior were examined. Crash sensitivity was also studied by using two different part fabrication methods and two crash test methods. The 12-sided components showed regular folding mode and excellent energy absorption capacity in axial crash tests.

Engine oils formulated using molybdenum dialkyldithiocarbamate, Mo(dtc)2, additives can provide substantial friction reduction under mixed to boundary lubrication conditions. It has been previously shown that the effectiveness of Mo(dtc)2 is significantly affected by the presence of other additives and by additive interaction and depletion processes occurring during use. In this study, ligand exchange reactions in an additive system containing Mo(dtc)2 and zinc dialkyldithiophosphate, Zn(dtp)2, have been investigated during oxidation in hexadecane and various base oils at 160°C. Samples of different composition obtained from these studies were used in investigations of the effects of original additives and ligand exchange products on friction reducing capability at 45 and 105°C.

The ability to evaluate the bending fatigue behavior of carburized low alloy steels in a laboratory and relate these measurements to performance of high contact ratio helical gears is important to the design and development of transmissions. Typical methods of evaluating bending fatigue performance of carburized gear steels do not directly represent helical planetary gears because they lack the geometric and loading conditions of planetary pinions. The purpose of this study is twofold; 1) development of a lab fatigue test to represent the fatigue performance of planetary pinion gears tested in a dynamometer and 2) evaluation of the influence of alloy content on bending fatigue performance of two steel alloys. The steels under evaluation were modified 8620M and 4615M alloys machined into bend bars with a notch representing a gear root and carburized to a case depth of approximately 0.35 mm (using the same carburizing cycle as the planetary pinion gears).

Structural adhesives are widely used across the automotive industry for several reasons like scale-up of structural performance and enabling multi-material and lightweight designs. Development engineers know in general about the effects of adding adhesive to a spot-welded structure, but they want to quantify the benefit of adding adhesives on weight reduction or structural performance. A very efficient way is to do that by applying analytical tools. But, in most of the relevant non-linear load cases the classical lightweight theory can only help to get a basic understanding of the mechanics. For more complex load cases like full car crash simulations, the Finite Element Method (FEM) with explicit time integration is being applied to the vehicle development process. In order to understand the benefit of adding adhesives to a body structure upfront, new FEM simulation tools need to be established, which must be predictive and efficient.

Variable amplitude torsion, bending, and combined torsion and bending fatigue tests were performed on an axle shaft. The moment inputs used were taken from the respective history channels of a cable log skidder vehicle axle. Testing results indicated that combined variable amplitude loading lives were shorter than the lives of specimens subjected to bending or torsion alone. Calculations using strain rosette readings indicated that principle strains were most active around specific angles but also occurred with lesser magnitudes through a wider angular range. Over the course of a biaxial test, cyclic creep narrowly limited the angles and magnitudes of the principal strains. This limitation was not observed in the calculated principal stress behavior. Simple life predictions made on the measured strain gage histories were non-conservative in most cases.

The effect of temperature and preload on the bolt load retention (BLR) behavior of AZ91D and AE42 magnesium die castings was investigated. The results were compared to those of 380 aluminum die castings. Test temperatures from 125 to 175°C and preloads from 7 to 28 kN were investigated. The loss of preload for AZ91D was more sensitive to temperature than that observed for AE42, especially at low preloads. In general, retained bolt-load was lowest in AZ91D. All test assemblies were preloaded at room temperature and load levels increased when the assemblies reached test temperature. The load-increase was dependent on the preload level, test temperature, alloy, and results from thermal expansion mismatch between the steel bolt and the magnesium alloy components, mitigated by the onset of primary creep. Thermal exposure (aging) of AZ91D at 150°C improved BLR behavior.

New high-temperature Mg alloys are being considered to replace 380 Al in transmission cases, wherein bolt-load retention, and creep, is of prime concern. One of these alloys is die cast AE42, which has much better creep properties than does AZ91D but is still not as creep resistant as 380 Al. It is thus important to investigate bolt-load retention and creep of AE42 as an initial step in assessing its suitability as a material for transmission housings. To that end, the bolt-load retention behavior of die-cast AE42, AZ91D and 380 Al have been examined using standard M10 bolts specially instrumented with stable high-temperature strain gages. The bolt-load retention test pieces were die cast in geometries approximating the flange and boss regions in typical bolted joints. Bolt-load retention properties were examined as a function of time (at least 100 hours), temperature (150 and 175 °C) and initial bolt preload (14 to 34 kN).

This paper presents the design and operation of a new stepped bore master cylinder (fast-fill) which also integrates the rear brake proportioning valves and brake failure warning device in one major assembly. This design optimizes weight, performance and package together with several unique design features. It incorporates a combination of a plastic reservoir, permanent mold aluminum body, steel pistons, and minaturized steel proportioning valves resulting in a significant weight and cost reduction versus equivalent hydraulic actuation systems.

All automotive brake linings have mechanical strength and thermal expansion properties which vary with orientation. This paper describes laboratory equipment and test procedures which characterize lining strength and expansion behavior, using small specimens. A benchtop testing device is introduced which can be used to perform shear and tensile tests on lining samples and singly-riveted lining assemblies. Results are presented for a representative group of production and experimental linings. Applications are discussed.

A new methodology for determining the steady-state flow force on a hydraulic spool valve has been developed. From a solid model of the valve and valve body, a commercially available CFD package automeshes the volume grid and determines the 3D steady-state flow field and forces on the valve within 36 CPU hrs. This numerical approach enables the quick determination of optimal valve design aimed at improved valve controllability and reduced wear in the hydraulic circuit. To demonstrate this methodology, several simulations were performed aimed at investigating the influence of valve design and valve operating conditions on the steady-state flow force experienced by the valve. The numerical simulations showed that a tapered spool geometry can introduce significant variations in the axial and radial forces (30%).

IN THE first part of this paper dealing with the metallurgical aspects of the camshaft-tappet problems met with in the design of the new Ford overhead-valve V8 engines, Messrs. Laird and Stevens describe the events which led to the adoption of the as-cast alloy-iron camshaft, nitro-carburized martensitic tappet combination. The combination cited works well in the engines described, but it is not implied that it will perform satisfactorily elsewhere. In the second portion of the paper, Mr. Iles discusses the test schedule devised in connection with the development of the camshaft-tappet materials in the new engines. It is stated that important findings will occur when such tests involve a large number of parts, making possible the study of results on a frequency basis. Tests have shown that a predominantly martensitic tappet structure results in superior performance in combination with the as-cast alloy-iron camshaft used.

THE study of engine life, carried out by investigating engine wear in typical service, and by then striving to find the most effective ways of controlling it, forms the basis of this paper on contaminants in lubricants. The investigation involved a study of engine wear in 20,000 miles of operation typical of the average driver. The average driver was selected by using test cars from an employee transportation car pool. At the conclusion of the tests it was found that the use of the full-flow oil filter proved to be the best method for restricting engine wear caused by contaminants that get inside the engine. It was also shown that after successfully eliminating large, solid particles, further restriction of engine wear would depend upon the ability of the oil to lubricate, and upon the engine design to provide the oil supply in a manner suitable for lubrication of each part of the engine.

Automotive fuel vapor emissions that would otherwise evaporate into the atmosphere are being captured in activated carbon vapor storage canisters. Fuel vapor is loaded into the canisters via a direct connection to the fuel tank vapor dome. Hydrocarbons are desorbed from the activated carbon into the engine combustion cylinders using engine intake vacuum. The carbon canister capacity requirements have increased in recent years in order to meet both Enhanced Evaporative Emission regulations and the Clean Air Act emission requirements for On-board Refueling Vapor Recovery (ORVR). The higher capacity requirements have generated the need for larger volume canisters that can meet the emission requirements and still be designed within the space and packaging limits of the vehicle application. This paper describes the simultaneous engineering approach used at Ford Motor Company to design a large volume cylindrical shaped carbon canister.

It is frequently desirable to construct a characterization of vehicle deceleration which is significantly simplified from its actual time history. A number of interesting techniques have been developed to perform this characterization based upon polynomial and Fourier-type series approximations and utilizing goodness of fit criteria related to both least squared error and the satisfaction of boundary conditions. Extensive mathematical occupant simulations indicate that characterizations involving as few as four parameters are adequate to describe the primary effects of complex vehicle deceleration time histories as they influence occupant dynamics with conventional restraint systems.

In September 1993, the Partnership for a New Generation of Vehicles (PNGV) program, initiated a cooperative research and development (R&D) program between the federal government and the United States Council Automotive Research (USCAR) to develop automotive technologies to reduce the nation's dependence on petroleum and reduce emissions of greenhouse gases by improving fuel economy. A key enabler for the attainment of these goals is a significant reduction in vehicle weight. Thus the major focus of the PNGV materials program is the development of materials and technologies that would result in the reduction of vehicle weight by up to 40%. The Automotive Lightweighting Materials (ALM) Program in the Office of Advanced Automotive Technologies (OAAT) of the Department of Energy (DOE), the PNGV Materials Technical Team and the United States Automotive Materials Partnership (USAMP) collaborate to conduct research and development on these materials.

The electroluminescence, a process where light is emitted by the recombination of electrically accelerating charges (electrons and holes) on a solid state chip, is the basis of light-emitting-diodes (LEDs) technology. Until the early 90s, LEDs were considered light sources of low efficiency. Nowadays, white high power, high efficiency LED's, based upon fluorophores are extremely promising for both vehicular / automotive and machinery usages. Associate with its high efficient light production, the long life capability of these devices keep improving their performance. In this study, three models of LEDs, from two different manufacturers were used.

In design for durability, it is generally believed that a compressive mean stress is beneficial and a tensile mean stress is detrimental. Quantitatively the effect of mean stress on fatigue life however is still inconclusive and may very well depend on both the material used and the loading conditions. Over the years, many models have been proposed to help predict mean stress effects. For example, in the long life region, Goodman's formula is widely used, while the Smith-Watson-Topper damage parameter seems the most popular for use in computerized local strain based fatigue tools. In this paper, several frequently cited mean stress correction methods together with the most recent crack closure based method are compared in various ways. Particular emphasis is given to the effect of yield level mean stresses, which has been traditionally neglected but is of practical importance to the ground vehicle industry.